Border Garage Door HelpCall (956) 394-2058

Garage Door Won't Close? Check the Sensors First

Short answer: When a garage door starts to close and then goes back up, the safety sensors are the usual cause. Something is blocking the beam, a lens is dirty, or a sensor got knocked out of line. You can safely check those three things yourself. If the door still won't close, or if it won't reverse when it should, call a provider.

Call (956) 394-2058

How the safety sensors work

Safety sensors and the 2x4 reverse test The bottom of a garage door coming down. Two small safety sensors sit on each side of the opening, 4 to 6 inches above the floor, with a beam between them. A 2x4 board lies flat on the floor in the door's path; the door should reverse when it touches the board. door closing 4–6 in. 2×4 laid flat Safety sensors Door touches the board → it must go back up
Safety sensors sit 4 to 6 inches above the floor. Test the reverse with a 2×4 laid flat in the door's path (CPSC).

Most automatic openers have two small sensors, one on each side of the door, close to the floor. One sends an invisible beam across the opening and the other receives it. If anything breaks the beam while the door is closing, the opener stops and sends the door back up.

The U.S. Consumer Product Safety Commission (CPSC) says these electric eyes should be mounted 4 to 6 inches above the floor. Openers made or imported for sale in the U.S. after January 1, 1991 must have a reversing system, and external protection like these sensors was added as a requirement in 1993.

Safe checks you can do

1. Clear the path

Look along the bottom of the door opening. A box, a bike tire, a broom, even a spider web or tall grass in front of a sensor can break the beam.

2. Clean the lenses

Wipe both sensor lenses with a soft, dry cloth. Dust and grime can block the beam.

3. Look at the sensor lights

Many sensors have a small light. On Chamberlain-made openers, for example, the company's support site says the sending sensor shows an amber light and the receiving sensor a green one. Both steady means the sensors are aligned and talking to each other. A green light that's off or blinking usually means they're out of line, and both lights off can mean the sensors aren't getting power. Other brands use their own patterns, so check your opener's manual.

4. Check the alignment

Sensors get bumped by cars, bikes and trash cans. If one is pointing up, down or sideways, it may not "see" the other one. If the bracket is loose, bent or the wire is damaged, that's a job for a provider.

5. Try the wall button

Chamberlain's support site suggests a quick check: with the path clear of people, pets and objects, press and hold the wall button until the door is fully closed. If the door closes only while you hold the button, the sensors need attention. Watch the door the whole way down, and get the sensors fixed rather than closing it this way every day. Not every opener responds the same way.

Run the 2×4 reverse test

The sensors are only half of the safety system. The CPSC recommends testing the reverse feature like this:

  1. Put a 2×4 board flat on the floor, centered under the door.
  2. Press the button to lower the door.
  3. The moment the bottom edge hits the board, the door has to stop and head back up.

If it doesn't reverse, the CPSC says to disconnect the opener and leave it off until it's adjusted using the owner's manual, repaired or replaced. The CPSC suggests inspecting the door and opener every 30 days.

Keep the wall button high enough that small kids can't reach it, and keep the remotes away from them, as the CPSC advises.

When it's not the sensors

If the sensors are clean, lined up and the lights look right, something else may be going on:

  • The door hits a snag in the track and the opener reverses because it feels resistance.
  • The force or travel settings are off, so the opener thinks the door hit something.
  • A spring or cable problem makes the door heavy or uneven. If you heard a bang or see a gap in the spring above the door, stop using the opener. Broken spring: what to do
  • The opener itself is failing. HomeAdvisor puts opener life at about 10 to 15 years.

These need a provider. Adjusting force settings, tracks or springs isn't a safe DIY fix.

What a repair might cost

National figures from HomeAdvisor:

Repair National figure
Sensor realignment $150 to $250 (2025)
Average opener repair $232, most between $124 and $366 (2022)

These are national figures, not Laredo prices. The provider will confirm the price before any work.

Garage door won't close FAQ

Why does my garage door go down and then back up?

The sensors think something is in the way. Clear the path, clean the lenses and check that both sensors point at each other. If that doesn't help, the opener's settings or the door itself may need attention.

Why do the sensor lights keep blinking?

On Chamberlain-made openers, a blinking or dark green light on the receiving sensor usually means the sensors are out of alignment. Other brands differ, so check your opener's manual.

Is it safe to keep using a door that doesn't reverse?

No. The CPSC says to disconnect the opener until it's fixed.

Why does my garage door open but not close?

Almost always the sensors. Less often, it's the opener's settings or a track problem.

Still won't close? Call

Tell the provider what the door does, how far it goes and what the sensor lights show.

Call (956) 394-2058

Related: garage door repair in Laredo · garage door opener repair · off-track and cable repair · broken spring: what to do now

Sources

Last updated: November 17, 2026

Call (956) 394-2058
MenuClose